Hughes DW 3000 One-Way Installation Manual Download Page 43 | Manualshive

Page: 43 / 48

background image

39

POINTING THE SATELLITE DISH

TOOLS NEEDED

• Compass
• 1/2-inch open-end or socket wrench
• 7/16 open-end wrench
• Torque wrench (can accept 1/2-inch socket and exert 12 ft-lbs. of

torque)

• Wrench
• Permanent marker

• Pencil

This section describes how to point the satellite dish at the sat-
ellite. Correct alignment is critical to the operation of the sys-
tem. When the satellite dish is pointed directly at the satellite, it
receives a strong signal. If it is not positioned properly, the sig-
nal may be weak, and errors may result during data transfers.

The values calculated by the satellite dish pointing software are
accurate enough to allow you to acquire the satellite signal on
the first try if the satellite dish mast is plumb.

THE ITERATIVE PROCESS OF POINTING THE DISH

You will be making three adjustments on your satellite dish:
polarization (rotation of the satellite dish), azimuth (pointing
side to side), and elevation (pointing up or down). These terms
are defined on page 6.

Pointing the satellite dish is an iterative process. That is, you go
through cycles of making small adjustments to the satellite dish
until you are satisfied you cannot get a stronger satellite signal.
When you have achieved the strongest possible signal, you
have peaked the signal.

Begin by peaking the azimuth setting; then peak the elevation
setting; and then readjust the azimuth setting if necessary. After
you have optimized the azimuth and elevation settings, you
may find that making adjustments in the polarization setting
affects the optimum azimuth and elevation settings, and you
must go back and adjust them again.

You may achieve the strongest signal strength after just a few
adjustments, or you may find that several adjustments are
needed. Remember that by getting the strongest possible signal
you ensure that you can use all your system’s capacity.

Figure 50

Elevation bolt

Mast

Azimuth Reference Marks

(made by user)

Polarization
scale

Satellite
dish

Elevation
scale

«
...
41
42
43
44
45
...
»

Summary of Contents for DW 3000 One-Way

















































Reviews:

No comments

Related manuals for DW 3000 One-Way

Brand: Ubiquiti Pages: 24

FIND4/GPS D4/SHK 4 Series

Brand: Panorama Antennas Pages: 12

StarterDish 21 UM

Brand: RF Elements Pages: 19

Satellite Radio Antenna

Brand: Sirius Satellite Radio Pages: 10

Brand: TRENDnet Pages: 2

Brand: M2 Antenna Systems Pages: 9

Brand: BandLuxe Pages: 14

Brand: Televes Pages: 4

Brand: Shively Labs Pages: 28

Brand: Winnix Technologies Pages: 3

Brand: TracVision Pages: 23

Super USB WiFI 3

Brand: C. Crane Pages: 16

Brand: cable matters Pages: 8

Brand: Labgear Pages: 2

Brand: Aerohive Networks Pages: 111

Brand: fanfare Pages: 2

Brand: Hama Pages: 38

Brand: Panorama Antennas Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands