background image

 • About this document

 

1036332-0001  Revision C

xi

About this document

Scope and audience

This manual describes components and features that are unique to 
the DIRECWAY DW7700 remote terminal. This manual 
supplements the 

Remote Terminal User Guide, Models: DW7000, 

DW7700

 (1035978-0001).

This manual is addressed to users in both the United States and 
International countries. Certain procedures, contact information, 
parts, and other operational considerations may vary depending 
on the user’s location. This manual clearly identifies those 
differences when applicable.

Organization and 

updates

This manual is organized into the following chapters:

Chapter 1 – 

Introduction

 gives an overview of the DW7700.

Chapter 2 – 

DW7700 component and feature descriptions

 

describes the components and features that distinguish the 
DW7700 from the DW7000. 

Chapter 3 – 

DW7700 LEDs

 describes the DW7700 LEDs.

Chapter 4 – 

DW7700 System Control Center

 describes the 

DW7700 System Control Center used to access important 
DW7700 system information.

Appendix A – 

Conforming with standards and directives

 lists 

standardsd and directives that apply to the DW7000 and 
DW7700.

There is also a list of acronyms and abbreviations and index at the 
end of the manual.

Summary of Contents for DiRECWAY DW7700



















































Reviews: