background image

Chapter 2 • Antenna parts and required tools

 

14

1037749-0001  Revision B

Tools

Table 2 lists the tools required to assemble and install the 
antenna. 

Table 2:  Tools required to assemble and install the antenna

Tool

Details

Socket wrench, ½-inch

 

(with 3-inch extension)

For 5/16-inch bolts.

Open-end wrench, 
½-inch

For 5/16-inch bolts. Two of the Az/El 
canister nuts are not accessible by socket 
wrench. Some nuts and bolts require a 
second wrench to prevent turning.

2 open-end or socket 
wrenches, 7/16-inch

For 1/4-inch bolts. Some nuts and bolts 
require a second wrench to prevent turning.

Torque wrench 

With ½-inch and 7/16-inch sockets capable 
of torquing to 8 ft-lb.

Long-shaft hexagonal 
ball driver (7/64-inch)

For #6-32 Allen screws. Driver shaft should 
be at least 5 inches long.

Phillips-head 
screwdriver, 1/4-inch

For screw used to help secure antenna 
reflector to reflector bracket.

Bubble level 

Used to make sure that the mast is plumb.

Compass

Used in determining antenna azimuth.

Pencil

Carpenter’s pencil.

Weather grade silicon 
sealant

Used to keep moisture away from cable 
connections.

Weatherproofing tape

Used to keep moisture away from cable 
connections

Approved RG6 cable

Used for IFL between IDU and antenna.

UV-rated cable ties

Used to secure slack in cables to antenna 
mast.

Summary of Contents for AN8-074P































































Reviews: