Hubsan H101 Instruction Manual Download Page 8

Page: 8 / 10

4.2.4. RUDD REVERSE SET UP

Hold down the ENT key for 1 second to enter the setting status, and then press the

DN key repeatedly until the RUDD symbol starts to flash, the current status NOR or

REV will be displayed. Press ENT key to choose REV and then press EXT key for 2

seconds to confirm and exit.

flashing

4.2.5. EXPERT MODE REVERSE SET UP

Hold down the ENT key for 1 second to enter the setting status, and then press the

DN key repeatedly until the EXPERT symbol starts to flash, the current status NOR

or REV will be displayed. Press ENT key to choose REV and then press EXT key for

2 seconds to confirm and exit.

flashing

4.3

SENSITIVITY SET UP

4.3.1 RUDDER SENSITIVITY SET UP- NOR MODE

Hold down the ENT key for 1 second to enter the setting status, and then press the

DN key repeatedly until the three-point dotted line symbol starts to flash(see

picture below), press RUDDER TRIM key to idea sensitivity and then press EXT

key for 2 seconds to confirm and exit.

EXT

ENT

DOWN

EXT

ENT

DOW

EXT

ENT

DOWN

EXT

ENT

DOWN

6.2 Effect of Control

CAUTION: To avoid loss of control: ALWAYS move the controls S-L-O-W-L-Y! Be

aware that control inputs will reduce available lift (see ‘Helicopter Principles of

Flight’).Be ready to use a little extra Throttle to maintain height during maneuvers.

Throttle (Collective Power) increases/decreases the Flying Height of your helicopter

Rudder (Collective Torque Yaw) rotates your helicopter’s fuselage Left / Right

Elevator (Cyclic Pitch) moves your helicopter Forwards/Backwards

Aileron (Cyclic Roll) moves your helicopter ‘sideways’ Left/Right

MODE 2

EXT

ENT

DOWN

EXT

ENT

DOW

EXT

ENT

DOWN

EXT

ENT

DOWN

MODE 1

Summary of Contents for H101











Search results

Summary of Contents for H101

Reviews:

Related manuals for H101

Brands by name

Popular brands

Hubsan H101, Instruction Manual

Search results

Summary of Contents for H101

Reviews:

Related manuals for H101

Brands by name

Popular brands