background image

INSTALLATION MANUAL 

 

 

Page 5 of 15 

HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and 

accessories other than the ones recommended herein. Any installation performed by unqualified personnel  voids the product warranty provided by 

HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the 

general handling of these products please contact HUBER+SUHNER. 

 

Step 9 

Fix the power and fiber optic breakouts with suitable 
HUBER+SUHNER cable clamps. Depending on the number of 
breakouts and if power breakout cables are connectorised or 
not, different cable clamps are needed. Contact H+S sales office 
or see the cable clamp portfolio 
http://www.hubersuhner.com/en/products/fiber-optics to select 
the right cable clamps. 
The first clamps has to be applied 0.5m above the housing. The 
cable has to be fixed straight and in line with the MLEH 
enclosure. Do not bend breakout cable direct after the housing 
exit and avoid side load on the housing exit. 

 
Do not over bend the cables. Minimum bend 
radius for power cable and fiber optic cable is 10 
cm. Avoid side load on the power and fiber optic 
connector.  

 
 

All  connectors  (fiber  optic  and  power)  are  protected  using 
waterproof (IP67) protection caps.  

 

 

 

 

Step 10 

All connectors on the breakout cables are protected with water 
proof (IP67) protection caps. 
 

Do not remove the cap if no jumper cable is 
connected. When removing the cap instently mate 
the plug connector to avoid dirt entering the 
connector. 

 

Summary of Contents for MASTERLINE Extreme Hybrid
















Reviews: