Hubble AM-5 Manual Download Page 12

10

CURRENT LIMITING FUNCTION

The BMS has a advanced current limiting function built in. The charge current limiter is designed 

to activate if charging current has reached the maximum battery design charge limit. This ensures 

the battery does not disconnect from the circuit and the current limiter takes over and reduces the 

charge to 20Amps per battery.

The default start-up condition of the charging current limit is to start when the charging current 

is greater than 100A. After entering the current limit, the test will be performed again every 10 

minutes. When the current is less than the current limit start value, the current limit function will be 

turned off. When the current is bigger than the current limit start value, then the current limiting 

mode with stay enabled.

COMMUNICATION DESCRIPTION 

1.  The RS232 port is only for use with Hubble specific periphirals or technicians or at a service 

centre to interface with the BMS. Attempting to use this port for anything else or 3rd party 

products can cause damage. 

2.  The CAN Port is specifically to be used to any interfacing 3rd party equipment like inverters 

etc. This port is dedicated to inverters and other CAN bus ports for communication to get 

battery information. 

3.  The RS485 communication port can be interfaced with 3rd party inverters that does not 

have a CAN port and is supported by Hubble. 

4.  The Battery link ports are only for connecting more batteries of the same model to increase 

capacity and to enable multiple battery communications.

 

OPTIONAL CLOUDLINK DEVICE

The Hubble Cloudlink is an optional add-on to the Hubble X and AM range of products. As long 

as the device is connected to Wi-Fi it will cloud, all battery and inverter data to our cloud-server, 

enabling users to remotely monitor their power system.

Learn more about the Hubble Cloudlink here:  

https://www.hubblelithium.co.za/hubble-cloudlink.html 

 

Access the latest Coudlink Setup Guide here: 

https://www.hubblelithium.co.za/cloudlink-setup.html

Summary of Contents for AM-5
















Reviews: