Hubble AM-5 Manual Download Page 11

9

BUTTON OPERATION INSTRUCTIONS

 

• 

When the BMS is in sleep state, press the button for more than 1 S, the protection board is 

activated.

• 

When the BMS is in operating state, pressing the button more than 3 seconds and less than

• 

6 seconds, then the BMS will enter sleep state.When the BMS is in working state, the 
protection board will reset when the button is pressed for more than 6S.

BUZZER ACTION DESCRIPTION 

• 

In the case of short-circuit protection, the buzzer beeps every 2 seconds. If a short circuit is 

detected 3 times in a row then he short-circuit protection is locked, the buzzer will no longer 

beep. Disconnect the battery and wait a few minutes to switch it back on. It might take up to 

5 minutes to redetect a clear condition and then the BMS will re enable.

DESCRIPTION OF SLEEP FUNCTION

In order to reduce the power consumption of the whole system, the system has a sleep function.

When the following conditions are met, the system will enter the sleep mode: 

1.  The over-discharge protection of the BMS has not been released for 5 minutes.

2.  The duration of the standby state has reached 24 hours (no communication, no charge and 

discharge, no charger connected).

DESCRIPTION OF WAKE-UP FUNCTION

Please note that the battery enters sleep mode due to single or overall over-discharge, and 

cannot be activated or switched on by serial port or the comm ports. 

The BMS will activate and wake from sleep when the following is detected:

1.  If a charge current is applied to the battery from the inverter/ups.

2.  If the power button is pressed.

3.  Through communication from the RS232 or CANBus in certain circumstances.

interface

FUNCTIONS

     WARNING

Interfacing or plugging in any 3rd party or non approved Hubble products or periphirals into the RS232 

(serial) or RS485 (Battery Link) ports, can cause damage to the BMS and cause the BMS to malfunction. 

This may also result in damaging the internal cells. Plugging in non approved Hubble products into these 

ports can immediately void your warranty.

Summary of Contents for AM-5
















Reviews: