background image

Kim Floodlight 

Installation Instructions

  

WARNING:

 Fixtures must be grounded in accordance with local codes or the National Electrical Code. 

   

Failure to do so may result in serious personal injury.  

See back page for additonal safety warnings and cautions.

   AVERTISSEMENT: 

Les appareils doivent être mis à la terre conformément aux codes locaux ou au Code national de  

   

l’électricité. Ne pas le faire peut entraîner des blessures graves. 

Reportez-vous à la page précédente pour obtenir  

des avertissements et des mises en garde supplémentaires.

MAINTENANCE INSTRUCTIONS:       

Make certain electricity is 

off

 before beginning maintenance procedures.

INSTRUCTIONS D’ENTRETIEN:          

Assurez-vous que l’électricité est éteinte avant de commencer  

   

 

les procédures d’entretien.

1. For opening and closing of the fixture, refer to instructions and diagrams on instructions. 
2. A regularly scheduled maintenance program should be established to retain optimum light output and  

  reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optics.

Do not use alkaline or acid cleaners on reflector surfaces.
NOTE: 

All wiring must be done by a qualified electrician.

KEEP THIS SHEET FOR FUTURE REFERENCE.

!

!

!

!

06/10/19                 EC 190423101757                Rev A 

Part No.  93101452 

1.  

Apply silicone thread sealant to keep moisture out of J-Box.

2.  

Attach by turning fixture until snug on ring gasket and orient 
fixture. Do not overtighten.

Tools Required:

   

3/16" Allen Wrench    

q

 Silicone Thread Sealant

NOTE: 

Your fixture is equipped with a variable voltage driver which will accept input voltages  

from 120 thru 277 volts or 347 thru 480 volts depending on driver voltage specified.

STANDARD MOUNTING:
        Make certain electrical supply is OFF before starting fixture installation.

        Assurez-vous que l’alimentation électrique est à l’arrêt avant de commencer l’installation du luminaire.
The standard Architectural Floodlight mounts to any 

1/2" 

N.P.T. or 

1/2" 

N.P.S.M. female thread.   

Refer to junction box or other mounting device instructions for attachment to conduit system.

!

!

17760 Rowland St. 

City of Industry, CA 91748  

626/968-5666

Summary of Contents for Kim Lighting Floodlight













Reviews: