INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3):
NOTE: Cord and Hook/Loop ordered as CxHLPx
(Plug optional and ordered separately)
1. Insert end of Power Cord (A) through Hook/Loop (B). Supply cord is to be rated for a minimum of 90OC 16/3 SEOW-A/STOOW.
2. Insert end of Power Cord through the Cord Grip/Gotcha-ring (D),Rubber Bushing (E) and Washer (F). Note that the Rubber
Bushing is placed between the Cord Grip and Washer. Part of the cord jacket should extend through Bushing (E) and Washer
(F).
3. Insert the Power Cord through the Yoke Assy Crossmember (C) and into the Wiring Box ¾ Conduit hole, allowing the Washer
(F), Bushing (E) to “seat” inside. The Cord Grip (D) remains in place at the Hook/Loop.
4. Apply Teflon tape to the male (external) conduit thread of the Hook (A).
5. Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a wrench over the hex shape on the hook casting to tighten it in
place.
CAUTION: Do not twist the hook by using a screwdriver blade – too much force could break the hook.
6. Connect cord wires to the fixture AC Power Input Jumper Cord Ass’y, already factory installed into J-box, with approved wire
nuts. See wiring diagram for reference (page 3 and figure 6). Wires and wire nuts can now be pushed back into the
fixture/driver housing. Ensure grounding wires within wiring Box are secure.
7. Close out Wiring Box (G) using Cover, Cover Gasket, and Screws provided in hardware kit.
8. Mount wired Yoke Assembly (H) onto fixture rails using 5/16” Screw (J) provided in hardware kit into each pair of Slide Nut (K)
already inserted into the rail. Position the mounted Yoke Ass’y according to the centering illustration on page 10. Fine tuning
of the final Yoke Ass’y position on the rail may be required to achieve final balance and alignment.
9. Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.
10. Tighten Set Screw (F) to secure hook from loosening.
11. Secure Closure Backet (M) with Screw (N) provided.
12. Install lens option onto each Lightbar, see Figure 9. If wireguard was ordered, lenses will ship installed on fixture.
13. Complete electrical connection by installing AC Input Jumper Cord connector into AC Panel as shown in Figure 3.
INSTALLATION INSTRUCTIONS
Hubbell Lighting, Inc. Doc. No. 93062486
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
FIGURE 1
FIGURA 1
FIGURE 3
FIGURA 3
FIGURE 2
FIGURA 2
PAGE 1
WIRING BOX
3/4" OUTLETS
(G)
5/16 MNTG SCREW (J)
INTO RAIL SLIDE NUT (K)
TORQUE: 120 IN-LB
HHH (MODULAR HIGHBAY)
INSTALLATION INSTRUCTIONS
SEE WARNINGS ON CARTON
WARNINGS:
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
Disconnect power before installing or servicing.
The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Protect all wiring connections with approved insulators rated
600V, 150
O
C.
Line voltage must be 120V – 277V to match Fixture voltage
requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Upon receipt of this Fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held
accountable.
INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3):
NOTE: Cord and Hook/Loop ordered as CxHLPx
(Plug optional and ordered separately)
1.
Insert end of Power Cord (A) through Hook/Loop (B). Supply cord
is to be rated for a minimum of 90
O
C 16/3 SEOW-A/STOOW.
2.
Insert end of Power Cord through the Cord Grip/Gotcha-ring (D),
Rubber Bushing (E) and Washer (F). Note that the Rubber
Bushing is placed between the Cord Grip and Washer. Part of
the cord jacket should extend through Bushing (E) and Washer
(F).
3.
Insert the Power Cord through the Yoke Assy Crossmember (C)
and into the Wiring Box ¾ Conduit hole, allowing the Washer (F),
Bushing (E) to “seat” inside. The Cord Grip (D) remains in place
at the Hook/Loop.
4.
Apply Teflon tape to the male (external) conduit thread of the
Hook (A).
5.
Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a
wrench over the hex shape on the hook casting to tighten it in
place.
CAUTION:
Do not twist the hook by using a screwdriver blade –
too much force could break the hook.
6.
Connect cord wires to the fixture AC Power Input Jumper Cord
Ass’y, already factory installed into J-box, with approved wire
nuts. See wiring diagram for reference (page 3 and figure 6).
Wires and wire nuts can now be pushed back into the
fixture/driver housing. Ensure grounding wires within wiring Box
are secure.
7.
Close out Wiring Box (G) using Cover, Cover Gasket, and Screws
provided in hardware kit.
8.
Mount wired Yoke Assembly (H) onto fixture rails using 5/16”
Screw (J) provided in hardware kit into each pair of Slide Nut (K)
already inserted into the rail. Position the mounted Yoke Ass’y
according to the centering illustration on page 10. Fine tuning of
the final Yoke Ass’y position on the rail may be required to
achieve final balance and alignment.
9.
Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.
10.
Tighten Set Screw (F) to secure hook from loosening.
11.
Secure Closure Backet (M) with Screw (N) provided.
12.
Install lens option onto each Lightbar, see Figure 9. If wireguard
was ordered, lenses will ship installed on fixture.
13.
Complete electrical connection by installing AC Input Jumper
Cord connector into AC Panel as shown in Figure 3.
CLOSURE
BRACKET (M)
RETAINING
SCREW (N)
AFTER WIRING
ASSEMBLE YOKE
TO FIXTURE USING
RAIL MOUNTING
HARDWARE KIT
- SEE FIG. 3
D
E
F
A
B
YOKE
CROSSMEMBER
C
COMPLETE
YOKE ASS'Y
(H)
(CORDSETS
NOT SHOWN)
FIGURE 1a.
FIGURA 1a.
PLUG
(OPTION
AL)
CORD
ROUTE INTO
J-BOX WIRE TO
AC INPUT JUMPER
L
M
N
Hubbell Lighting, Inc. Doc. No. 93062486
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
FIGURE 1
FIGURA 1
FIGURE 3
FIGURA 3
FIGURE 2
FIGURA 2
PAGE 1
WIRING BOX
3/4" OUTLETS
(G)
5/16 MNTG SCREW (J)
INTO RAIL SLIDE NUT (K)
TORQUE: 120 IN-LB
HHH (MODULAR HIGHBAY)
INSTALLATION INSTRUCTIONS
SEE WARNINGS ON CARTON
WARNINGS:
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
Disconnect power before installing or servicing.
The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Protect all wiring connections with approved insulators rated
600V, 150
O
C.
Line voltage must be 120V – 277V to match Fixture voltage
requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Upon receipt of this Fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held
accountable.
INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3):
NOTE: Cord and Hook/Loop ordered as CxHLPx
(Plug optional and ordered separately)
1.
Insert end of Power Cord (A) through Hook/Loop (B). Supply cord
is to be rated for a minimum of 90
O
C 16/3 SEOW-A/STOOW.
2.
Insert end of Power Cord through the Cord Grip/Gotcha-ring (D),
Rubber Bushing (E) and Washer (F). Note that the Rubber
Bushing is placed between the Cord Grip and Washer. Part of
the cord jacket should extend through Bushing (E) and Washer
(F).
3.
Insert the Power Cord through the Yoke Assy Crossmember (C)
and into the Wiring Box ¾ Conduit hole, allowing the Washer (F),
Bushing (E) to “seat” inside. The Cord Grip (D) remains in place
at the Hook/Loop.
4.
Apply Teflon tape to the male (external) conduit thread of the
Hook (A).
5.
Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a
wrench over the hex shape on the hook casting to tighten it in
place.
CAUTION:
Do not twist the hook by using a screwdriver blade –
too much force could break the hook.
6.
Connect cord wires to the fixture AC Power Input Jumper Cord
Ass’y, already factory installed into J-box, with approved wire
nuts. See wiring diagram for reference (page 3 and figure 6).
Wires and wire nuts can now be pushed back into the
fixture/driver housing. Ensure grounding wires within wiring Box
are secure.
7.
Close out Wiring Box (G) using Cover, Cover Gasket, and Screws
provided in hardware kit.
8.
Mount wired Yoke Assembly (H) onto fixture rails using 5/16”
Screw (J) provided in hardware kit into each pair of Slide Nut (K)
already inserted into the rail. Position the mounted Yoke Ass’y
according to the centering illustration on page 10. Fine tuning of
the final Yoke Ass’y position on the rail may be required to
achieve final balance and alignment.
9.
Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.
10.
Tighten Set Screw (F) to secure hook from loosening.
11.
Secure Closure Backet (M) with Screw (N) provided.
12.
Install lens option onto each Lightbar, see Figure 9. If wireguard
was ordered, lenses will ship installed on fixture.
13.
Complete electrical connection by installing AC Input Jumper
Cord connector into AC Panel as shown in Figure 3.
CLOSURE
BRACKET (M)
RETAINING
SCREW (N)
AFTER WIRING
ASSEMBLE YOKE
TO FIXTURE USING
RAIL MOUNTING
HARDWARE KIT
- SEE FIG. 3
D
E
F
A
B
YOKE
CROSSMEMBER
C
COMPLETE
YOKE ASS'Y
(H)
(CORDSETS
NOT SHOWN)
FIGURE 1a.
FIGURA 1a.
PLUG
(OPTION
AL)
CORD
ROUTE INTO
J-BOX WIRE TO
AC INPUT JUMPER
L
M
N
Hubbell Lighting, Inc. Doc. No. 93062486
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Phone (864) 678-1000
Industrial Lighting
®
FIGURE 1
FIGURA 1
FIGURE 3
FIGURA 3
FIGURE 2
FIGURA 2
PAGE 1
WIRING BOX
3/4" OUTLETS
(G)
5/16 MNTG SCREW (J)
INTO RAIL SLIDE NUT (K)
TORQUE: 120 IN-LB
HHH (MODULAR HIGHBAY)
INSTALLATION INSTRUCTIONS
SEE WARNINGS ON CARTON
WARNINGS:
Observe all precautions usually followed when dealing with high
voltage equipment when installing or servicing this light fixture.
Disconnect power before installing or servicing.
The product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
Protect all wiring connections with approved insulators rated
600V, 150
O
C.
Line voltage must be 120V – 277V to match Fixture voltage
requirement.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Upon receipt of this Fixture, thoroughly inspect it for any damage.
If any is found, the carrier should be notified and held
accountable.
INSTALLING HOOK/LOOP MOUNT (See Figure 1, 2, & 3):
NOTE: Cord and Hook/Loop ordered as CxHLPx
(Plug optional and ordered separately)
1.
Insert end of Power Cord (A) through Hook/Loop (B). Supply cord
is to be rated for a minimum of 90
O
C 16/3 SEOW-A/STOOW.
2.
Insert end of Power Cord through the Cord Grip/Gotcha-ring (D),
Rubber Bushing (E) and Washer (F). Note that the Rubber
Bushing is placed between the Cord Grip and Washer. Part of
the cord jacket should extend through Bushing (E) and Washer
(F).
3.
Insert the Power Cord through the Yoke Assy Crossmember (C)
and into the Wiring Box ¾ Conduit hole, allowing the Washer (F),
Bushing (E) to “seat” inside. The Cord Grip (D) remains in place
at the Hook/Loop.
4.
Apply Teflon tape to the male (external) conduit thread of the
Hook (A).
5.
Thread the Hook (A) into the ¾” NPT Conduit Box (C). Use a
wrench over the hex shape on the hook casting to tighten it in
place.
CAUTION:
Do not twist the hook by using a screwdriver blade –
too much force could break the hook.
6.
Connect cord wires to the fixture AC Power Input Jumper Cord
Ass’y, already factory installed into J-box, with approved wire
nuts. See wiring diagram for reference (page 3 and figure 6).
Wires and wire nuts can now be pushed back into the
fixture/driver housing. Ensure grounding wires within wiring Box
are secure.
7.
Close out Wiring Box (G) using Cover, Cover Gasket, and Screws
provided in hardware kit.
8.
Mount wired Yoke Assembly (H) onto fixture rails using 5/16”
Screw (J) provided in hardware kit into each pair of Slide Nut (K)
already inserted into the rail. Position the mounted Yoke Ass’y
according to the centering illustration on page 10. Fine tuning of
the final Yoke Ass’y position on the rail may be required to
achieve final balance and alignment.
9.
Tighten the Yoke Ass’y mounting screws to torque noted in Fig. 3.
10.
Tighten Set Screw (F) to secure hook from loosening.
11.
Secure Closure Backet (M) with Screw (N) provided.
12.
Install lens option onto each Lightbar, see Figure 9. If wireguard
was ordered, lenses will ship installed on fixture.
13.
Complete electrical connection by installing AC Input Jumper
Cord connector into AC Panel as shown in Figure 3.
CLOSURE
BRACKET (M)
RETAINING
SCREW (N)
AFTER WIRING
ASSEMBLE YOKE
TO FIXTURE USING
RAIL MOUNTING
HARDWARE KIT
- SEE FIG. 3
D
E
F
A
B
YOKE
CROSSMEMBER
C
COMPLETE
YOKE ASS'Y
(H)
(CORDSETS
NOT SHOWN)
FIGURE 1a.
FIGURA 1a.
PLUG
(OPTION
AL)
CORD
ROUTE INTO
J-BOX WIRE TO
AC INPUT JUMPER
L
M
N
