background image

2

II Performance

2.1 Time

The machine can measure the natural parting and closing time of 12 metal fractures, the same period

time, the same period time, the same period time, the gold short time, the no flow time, the closing spring

time of the process of closing - parting, dividing - parting and dividing - dividing; Some models can

measure the pre-casting time of closing resistance.

2.2 Speed and stroke

This tester can record and measure the closing bounce time, the number of bounces, the bounce

process, and the bounce waveform of each fracture.

2.3 Speed and stroke

This tester can record and calculate the rigid points, rigidity, maximum speed, average speed, total

travel, opening distance, over travel, rebound amplitude, time-travel characteristic curve.

2.4 Current and voltage

This tester can record the opening / closing current value and current waveform of the opening /

closing coil, and provides DC5

270V / 10A (20A) digital adjustable circuit breaker operation power

supply, automatically completes the low voltage operation test of the circuit breaker, and measures the

open circuit. The operating voltage of the device.

2.5 Closing resistance

Some models of this machine can measure 6-way closing resistance value and its pre-throw time at

the same time.

III Term definitions

♦ Opening / closing time: When the opening / closing coil is powered on as the timing starting point, the

time to the opening / closing of the moving and static contacts.

♦ In the same period: Among the same phase, the difference between the maximum and minimum

opening / closing time.

♦ Phase-to-phase synchronization: The difference between the maximum and minimum opening / closing

time among three phases.

♦ Average speed: During the opening (closing) process, remove the front and back of the moving contact

by 10%, take the middle 80%, the ratio of the travel of the moving contact to time.

Summary of Contents for HZ7411




















Reviews: