D. Corner-mounted Installation/ 角装
Device Installation/ 设备安装
2
E. Wall-Mounted and Ceiling-Mounted Installations/ 壁装或吊装
Place the mount in the desired installation position.
.Use a marker to mark where the installation screws go.
Use a 10 mm bit to drill the holes to a depth of about
80 mm. Use a hammer to carefully drive the expansion
bolts into the holes. Then, remove the washers, the
spring washers, and the nuts from the expansion bolts.
将支架放置于安装位置 , 使用记号笔绘制螺钉安装位置，再
选择直径为 10mm 的钻头，钻取深约 80mm 的导孔。使用
羊角锤将膨胀螺栓打入钻好的孔内。 再将平垫、弹垫和螺母
拧下。
Remove washers, spring washers, and nuts from the
expansion bolts and thread the cables through the
wall mount. Put the four expansion bolts through
the four screw holes at the bottom of the wall
mount, replace the washers, spring washers, and
nuts on the expansion bolts, and tighten the nuts.
拧下膨胀螺栓上的平垫、弹垫和螺母。将需要与球机尾线
对接的线缆穿过壁装支架。将角装支架底座上的 4 个螺孔
套在相应的膨胀螺栓上，将平垫、弹垫和螺母套在膨胀螺
栓上，拧紧螺母。
3
5
Align the screw holes on the wall mount with
the screw holes on the pole mount, and fasten
them together using the M8 screws.
将角装支架上的螺孔与抱装支架上相应的螺孔对齐，
拧紧 M8 螺钉。
1
NOTE/ 说明
For details about subsequent
installation operations, see 3 to
5 in
Pole-mounted Installation
.
后续安装的具体过程请参见“立杆
抱装中的步骤3到步骤5”。
2
1
Remove washers, spring washers, and nuts from the expansion bolts, and thread the cables through the mount.
Put the four expansion bolts through the four screw holes on the base of the mount, replace the washers,
spring washers, and nuts on the expansion bolts, and tighten the nuts.
拧下膨胀螺栓上的平垫、弹垫和螺母。将需要与球机尾线对接的线缆穿过壁装 / 吊装支架。将壁装 / 吊装支架底座上的 4
个螺孔套在相应的膨胀螺栓上，将平垫、弹垫和螺母套在膨胀螺栓上，拧紧螺母。
NOTE/ 说明
For details about subsequent installation
operations, see 3 to 5 in
Pole-mounted
Installation
.
后续安装的具体过程请参见“立杆抱装中的
步骤3到步骤5”。
wall-mounted/ 壁装
ceiling-mounted/ 吊装
wall-mounted/ 壁装
ceiling-mounted/ 吊装
Place the mount in the desired installation position. Use a marker to mark the screw installation locations.
Select a drill bit with a diameter of 10 mm to drill holes with a depth of about 80 mm. Use a claw hammer to
install the expansion bolts into the holes. Then, screw off the flat washers, spring washers, and nuts from the
expansion bolts.
将支架放置于安装位置 , 使用记号笔绘制螺钉安装位置。再选择直径为 10mm 的钻头，钻取深约 80mm 的导孔。使用羊
角锤将膨胀螺栓打入钻好的孔内。 再将平垫、弹垫和螺母拧下。
