Huawei UPS5000-E-125K-HABBS-01 Quick Manual Download Page 6 | Manualshive

Page: 6 / 20

background image

6

Connecting Power Cables

3.2

Scenario 1: Routing Cables from the Top

The cabling route is for reference only. Connect cables based on site requirements.

1. Remove the insulation protective panel from

the rear of the cabinet and remove covers
from the top as required.

2. Connect a ground cable to the UPS cabinet.

ATS input

3. Connect the AC input power cable.

MCCB input

«
...
4
5
6
7
8
...
»

Summary of Contents for UPS5000-E-125K-HABBS-01





















Reviews:

No comments

Related manuals for UPS5000-E-125K-HABBS-01

Brand: Falcon Pages: 47

Brand: Salicru Pages: 2

Brand: Delta Pages: 80

Brand: CyberPower Pages: 2

Brand: Leonics Pages: 7

Brand: Leonics Pages: 13

NetPower NPW 1000

Brand: Riello UPS Pages: 6

SENTINEL DUAL SDL 10000

Brand: Riello UPS Pages: 196

SANUPS E11A102U

Brand: Sanyo Denki Pages: 71

Brand: Tripp Lite Pages: 3

SmartPro VS SMART3000VS

Brand: Tripp Lite Pages: 5

Brand: Tripp Lite Pages: 7

SmartPro SMX3000XLRT2UA

Brand: Tripp Lite Pages: 6

SmartPro SMART5000RT3U

Brand: Tripp Lite Pages: 6

Brand: Tripp Lite Pages: 18

SmartPro SMART1000RM2U

Brand: Tripp Lite Pages: 60

Line Interactive UPS Series CS500B

Brand: OPTI-UPS Pages: 1

Brand: Cuppon Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands