Huawei UPS2000-A-10 kVA User Manual Download

Page: 137 / 152

UPS2000-A-(6 kVA-10 kVA)
User Manual

B Alarm Handling

Issue 04 (2019-05-05)

130

Alarm
Name

Alar
m
Ident
ifier
(Alar
m ID)
Web
UI
Deci
mal
Syste
m

Alarm
Identi
fier
(Alar
m ID)
LCD
Heuri
sticim
al
Syste
m

Alarm
level

Alarm
Clear
Mode

Impact on the
System

Repair Proposal

Measure: Contact Huawei technical
support.

Batt.
reverse

14-1

20-1

Critical

Autom
atic
clear

This alarm does
not affect the
UPS or the
power supply.

Possible cause: The positive and
negative battery terminals are reversely
connected.

Measure: Check the battery
installation, and install batteries again.

No
battery

16-1

22-1

Minor

Autom
atic
clear

This alarm does
not affect the
power supply.



Possible cause: No batteries are
connected.

Measure: Connect batteries.



Possible cause: The batteries are in
poor contact.

Measure: Check the battery cable
connection. If battery cables are
loose, connect them securely.

Battery
overtemp
erature

17-1

23-1

Minor

Autom
atic
clear

An alarm is
generated, and
the battery
lifespan is
affected.

Possible cause: The temperature inside
the UPS of the standard version or the
ambient temperature exceeds the
battery overtemperature alarm
threshold (default value: 50º

C).

Measure: Reduce the ambient
temperature and keep the air intake and
exhaust vents of the UPS unblocked.

Battery
overvolta
ge

19-1

25-1

Minor

Autom
atic
clear

An alarm is
generated, and
the battery
lifespan is
affected.



Possible cause: The battery voltage
reaches the alarm threshold due to
continuous charge.

Measure: When batteries are in
charge mode, wait for 2 minutes
and check whether the alarm is
cleared.



Possible cause: The number of
batteries configured is less than the
actual number of batteries.

Measure: Check whether the
number of batteries is correctly set.

Summary of Contents for UPS2000-A-10 kVA

























































































































































Search results

Summary of Contents for UPS2000-A-10 kVA

Reviews:

Related manuals for UPS2000-A-10 kVA

Brands by name

Popular brands

Huawei UPS2000-A-10 kVA, User Manual

Search results

Summary of Contents for UPS2000-A-10 kVA

Reviews:

Related manuals for UPS2000-A-10 kVA

Brands by name

Popular brands