Huawei TP3206 Installation Manual Download

Page: 48 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

7 Installing HD Displays

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

Installing HD Displays

About This Chapter

This chapter describes how to install the HD displays.

7.1 Parts List

7.2 Installation Procedure

7.3 Installation Effect

7.1 Parts List

Before installing the HD displays, prepare the parts listed in

Table 7-1

Table 7-1

HD display parts list

No.

Name

Quantity

Camera

Power cable

Video cable

Serial cable

HD display

HD display base (A11)

3 x 2

NOTE

Two types of HD

displays are

available, and they

correspond to

different bases. The

two types of bases

are both delivered

with the

telepresence system.

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands