Huawei SUN2000-42KTL User Manual Download Page 96

Page: 96 / 105

SUN2000-(36KTL,42KTL)
User Manual

9 Handling the SUN2000

Issue Draft A (2016-05-30)

Huawei Proprietary and Confidential

Handling the SUN2000

9.1 Removing the SUN2000

Before removing the SUN2000, disconnect both the AC and DC power supplies. For
processes of disconnecting the power supplies, see

6.3 Powering Off the SUN2000

. After

powering off the SUN2000, wait at least 5 minutes before performing operations on it.

Perform the following operations to remove the SUN2000:

Disconnect all cables from the SUN2000, including RS485 communications cables, DC
input power cables, AC output power cables, and PGND cables.

Remove the SUN2000 from the mounting bracket.

Remove the mounting bracket.

9.2 Packing the SUN2000



If the original packing materials are available, put the SUN2000 inside them and then
seal them by using adhesive tape.



If the original packing materials are unavailable, put the SUN2000 inside a suitable hard
carton and seal it properly.

9.3 Disposing of the SUN2000

If the SUN2000 service life expires, dispose of it according to the local disposal rules for
electrical equipment waste.

Summary of Contents for SUN2000-42KTL










































































































Search results

Summary of Contents for SUN2000-42KTL

Reviews:

Related manuals for SUN2000-42KTL

Brands by name

Popular brands

Huawei SUN2000-42KTL, User Manual

Search results

Summary of Contents for SUN2000-42KTL

Reviews:

Related manuals for SUN2000-42KTL

Brands by name

Popular brands