Huawei SmartAX MA5616 Configuration Manual Download

Page: 464 / 553

Figure 9-10

Example network for configuring the VLAN stacking wholesale service

BRAS

User1

User2

User3 User4

VLAN ID:100

VLAN ID:101

BRAS

MA5616

ISP1

ISP2

Modem

LAN Switch

Data Plan

Table 9-6

provides the data plan for configuring the VLAN stacking wholesale service.

Table 9-6

Data plan for configuring the VLAN stacking wholesale service

Item

Data

ISP 1 user group

Uplink port: 0/0/1

Network-side VLAN ID (outer VLAN tag): 100

VLAN attribute: stacking VLAN

User 1:

Access port: 0/1/0

Inner VLAN tag: 11

User 2:

Access port: 0/1/1

Inner VLAN tag: 12

ISP 2 user group

Uplink port: 0/0/1

Network-side VLAN ID (outer VLAN tag): 101

VLAN attribute: stacking VLAN

User 3:

Access port: 0/1/2

Inner VLAN tag: 11

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

453

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands