Huawei RTN 380H Quick Installation Manual Download Page 29 | Manualshive

Page: 29 / 29

background image

Installation Reference

56/57 >>

1

Installing the WLAN Module

Loading NE Data

RSSI/NMS
maintenance
compartment

Connected to the Web LCT

Connected to the USB flash drive

Ports within the
maintenance
compartment

RSSI/NMS
maintenance
compartment

Ports within the
maintenance
compartment

Open the RSSI/NMS maintenance compartment.

Check the USB port status indicator.
After data is loaded from the USB flash drive to the
RTN 380, the USB port status indicator in the
USB/RSSI/NMS port should be on (green).

1

Optional:

Insert the USB flash drive into the USB port.

2

3

Optional:

Connect the computer where the Web LCT is

installed to the RJ45 port.

Close and screw the maintenance compartment.

The USB flash drive loads software, system parameters, and scripts for commissioning
a newly deployed equipment.
For the functions, working principles, and types of USB flash drives supported, see the

Product Description

.

NOTE

For a description of the indicator on the USB flash drive, see the

Commissioning and

Configuration Guide

.

NOTE

WLAN module

Open the RSSI/NMS maintenance compartment.

1

Insert the WLAN module into the USB port.

2

3

Optional:

Connect the Web LCT to the equipment through WLAN.

Close and screw the maintenance compartment.

For information about how to connect the Web LCT to the equipment through WLAN,
see the C

ommissioning and Configuration Guide.

«
...
27
28
29

Summary of Contents for RTN 380H






























Reviews:

No comments

Related manuals for RTN 380H

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Zeagle Pages: 37

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: Panamax Pages: 16

Brand: York Pages: 24

Real Living iM1

Brand: Yale Pages: 2

Brand: K&K Pages: 10

Brand: Automated Logic Pages: 10

Brand: Ezodo Pages: 7

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Runxin Pages: 4

Brand: Wavelength Electronics Pages: 17

Brand: OBO Bettermann Pages: 6

Brand: NI Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands