Huawei RRU3268 Installation Manual Download Page 53

Page: 53 / 131

Installation engineer C pulls the lifting sling downwards, and installation engineer D pulls
the traction sling outwards to protect the fiber optic cables from colliding with the tower.

Step 2

Secure the fiber optic cables to the tower vertically using cable clips.

Step 3

Remove the lifting sling, traction sling, and protection pipe.

NOTE

The procedure for hoisting the fiber optic cables onto the tower is for your reference only.

----End

7.3 Hoisting Power Cables onto a Tower

This section describes the procedure for hoisting power cables onto a tower and the precautions
that must be taken.

Context

Cabling requirements for power cables are met. For details, see

9.1 Cabling Requirements

The procedure for adding a connector to the RRU power cable on the RRU side is done under
the tower.

Procedure

Step 1

Hoist the power cables onto the tower, as shown in

Figure 7-9

RRU3268
Installation Guide

7 Hoisting an RRU and Related Cables onto a Tower

Issue ()

Huawei Proprietary and Confidential

Summary of Contents for RRU3268




































































































































Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands

Huawei RRU3268, Installation Manual

Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands