Huawei RRU3268 Installation Manual Download Page 101

Page: 101 / 131

Fiber optic cables are used within the temperature range of -40°C to 60°C. If the current
temperature is out of the range, make protection measures or route the cables again.

Cables are routed in an untangled and orderly fashion.

Do not bind fiber optic cables at turns.

Do not stretch, step on, or place heavy objects on fiber optic cables. Keep the cables away
from sharp objects.

When fiber optic cables are routed, the excess of the cables must be coiled around special
devices, such as a fiber coiler.

When coiling fiber optic cables, apply even strength. Do not bend the cables with force.

Vacant optical connectors must be covered with dustproof caps.

Fiber optic cables cannot be squeezed by the cabinet door when routed through the cabinet,
as shown in

Figure 9-4

CPRI fiber optic cables routed through the cabinet (1)

Figure 9-5

CPRI fiber optic cables routed through the cabinet (2)

RRU3268
Installation Guide

9 Installing RRU Cables

Issue ()

Huawei Proprietary and Confidential

Summary of Contents for RRU3268




































































































































Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands

Huawei RRU3268, Installation Manual

Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands