Huawei RRU3268 Installation Manual Download Page 116

Page: 116 / 131

NOTE

Open the clip only for the associated cable.

Figure 9-20

Opening clips

Step 4

Remove the waterproof block.

NOTE

Remove only the waterproof blocks for the cables to be installed.

----End

9.10 Installing an RRU Power Cable

This section describes the procedure for installing an RRU power cable.

Prerequisites

An easy power receptacle (pressfit type) connector is added to the RRU power cable on
the RRU side. For details, see

12.1 Adding a Tool-Less Female Connector (Pressfit

Type) to the RRU Power Cable on the RRU Side

Add a connector or OT terminals to the RRU power cable on the power device side. For
details, see the

DBS3900 Installation Guide

Context

There are two types of RRU power cables in terms of cross-sectional areas: 3.3 mm

(0.005 in.

) (12 AWG) complying with North American standards and 4 mm

(0.006 in.

) complying with

European standards.

RRU3268
Installation Guide

9 Installing RRU Cables

Issue ()

Huawei Proprietary and Confidential

108

Summary of Contents for RRU3268




































































































































Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands

Huawei RRU3268, Installation Manual

Search results

Summary of Contents for RRU3268

Reviews:

Related manuals for RRU3268

Brands by name

Popular brands