Huawei RRU3232 Installation Manual Download Page 23

Page: 23 / 95

Figure 3-9

Angle steel specifications

CAUTION

It is recommended that only one RRU be installed on angle steel.

The vertical deviation angle of angle steel must be less than or equal to 10 degrees, as shown
in

Figure 3-7

Figure 3-10

shows an RRU installed on angle steel.

Figure 3-10

RRU installed on angle steel

Installing an RRU on a Wall

The wall on which RRUs are installed must meet the following requirements:

When a single RRU is installed, the wall has a capacity of bearing at least four times the
weight of the RRU.

Expansion bolts must be tightened to 30 N·m (265.52 lbf·in.) to ensure the bolts work
properly and the wall remains intact without cracks in it.

RRU3232
Installation Guide

3 Information About the Installation

Issue 05 (2011-10-20)

Huawei Proprietary and Confidential

Summary of Contents for RRU3232
































































































Search results

Summary of Contents for RRU3232

Reviews:

Related manuals for RRU3232

Brands by name

Popular brands

Huawei RRU3232, Installation Manual

Search results

Summary of Contents for RRU3232

Reviews:

Related manuals for RRU3232

Brands by name

Popular brands