Huawei ME909s Series Hardware Manual Download Page 45

Page: 45 / 76

HUAWEI ME909s Series LTE Mini PCIe Module
Hardware Guide

Electrical and Reliability Features

Issue 02 (2016-09-07)

Huawei Proprietary and Confidential

Table 5-4

Requirements for input current of the ME909s Mini PCIe module

Power

Peak (GSM 1 slot)

Normal (WCDMA) Normal (LTE 23 dbm)

VCC_3V3

3000 mA

800 mA

5.4.2

Power Consumption

The power consumptions of ME909s Mini PCIe module in different scenarios are
respectively listed in Table 5-5 to Table 5-10 .

The power consumption listed in this section is tested when the power supply of the
ME909s Mini PCIe module is 3.8 V, and all of test values are measured at room
temperature.

Table 5-5

Averaged standby DC power consumption of ME909s-821 Mini PCIe module

Description

Bands

Test Value (Unit: mA) Notes/Configuration

Typical

Sleep

LTE

LTE bands

2.0

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on the
network.

USB is in suspend.

TD-SCDMA

TD-SCDMA
bands

2.7

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on the
network.

USB is in suspend.

HSPA+/WCDMA UMTS bands

1.5

Module is powered up.

DRX cycle=7 (1.28s)

Module is registered on the
network.

USB is in suspend.

GPRS/EDGE

GSM bands

1.9

Module is powered up.

MFRMS=5 (1.175s)

Module is registered on the
network.

USB is in suspend.

Idle

LTE

LTE bands

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on the
network.

USB is in active.

Summary of Contents for ME909s Series













































































Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands

Huawei ME909s Series, Hardware Manual

Search results

Summary of Contents for ME909s Series

Reviews:

Related manuals for ME909s Series

Brands by name

Popular brands