Huawei LampSite Installation Manual Download

Page: 90 / 100

Figure 5-40

Removing the pRRU antenna housing

Step 2

Use a torque wrench with a torque of 0.6 N•m to connect the SMA straight male connector on
a jumper to the ANT port on the pRRU panel.

NOTICE

Tighten it with hands, and then use a torque wrench to tighten it with a rotational speed of less
than or equal to 2.4 rpm to tighten it.

Step 3

Connect the type N female connector of the jumper to the type N male connector of the RF feeder
connected to the built-in antenna.

NOTICE

Tighten the feeder close to the type N connector to ensure that the jumper is not tightened. In
this way, the connectors on both ends of a jumper are not affected by the external force.

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for LampSite





































































































Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands

Huawei LampSite, Installation Manual

Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands