Huawei BTS3900 V100R003 Hardware Description Download Page 164 | Manualshive

Page: 164 / 264

background image

Port/Switch

Function

Power supply test port

Measuring the power voltage by using a multimeter through the
-48V/+24V and 0V ports

TEST port

Testing

Battery control switch

Controlling the connection of the batteries through the ON and OFF
ports

l

Press and hold the ON port for 5s to 10s to connect to the
batteries.

l

Press and hold the OFF port for 5s to 10s to disconnect the
batteries.

CAUTION

l

You must insert a small round bar into the hole when you operate the
battery control switch. When you hear a crack, the batteries are connected
or disconnected.

COM port

Reserved for connecting to the external signal monitoring board

describes the LEDs on the panel of the PMU.

Table 4-66

LEDs on the panel of the PMU

Label

Color

Status

Description

RUN

Green

Blinking (on for 1s and
off for 1s)

The unit is functional, and the
communication with the BBU or upper-level
PMU is normal.

Blinking (on for 0.125s
and off for 0.125s)

The unit is functional, but the communication
with the BBU or upper-level PMU fails. If
the unit does not communicate with the BBU
or upper-level PMU for one minute, the
communication is regarded as failed.

On or off

The unit is faulty or the unit is in power-on
self-check state.

ALM

Red

On

The base station reports at least one of the
following alarms:

l

Mains overvoltage or undervoltage alarm

l

Busbar overvoltage or undervoltage
alarm

l

Alarm related to PSUs

l

Load disconnection alarm

Off

No alarm is reported.

4 BTS3900 Components

BTS3900

Hardware Description

4-72

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

Issue 04 (2011-02-15)

«
...
162
163
164
165
166
...
»

Summary of Contents for BTS3900 V100R003









































































































































































































































































Reviews:

No comments

Related manuals for BTS3900 V100R003

Brand: QUIETON Pages: 24

Brand: Quest Engineering Pages: 24

Brand: Nauticam Pages: 2

Brand: BAC Pages: 36

Brand: Baader Planetarium Pages: 6

BTL7-S5 B-M Series

Brand: Balluff Pages: 14

BML-S1G0 7 M5E 0 Series

Brand: Balluff Pages: 194

and Vantage Pro

Brand: DAVIS Pages: 4

and Vantage Pro

Brand: Davis Instruments Pages: 4

Brand: Datavideo Pages: 45

Brand: RaceChip Pages: 12

Brand: Ecco Pages: 9

Brand: Ecco Pages: 9

Brand: Saab Pages: 10

AERASGARD RCO2-W

Brand: S+S Regeltechnik Pages: 7

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands