Huawei BTS3900 V100R003 Hardware Description Download Page 144

Page: 144 / 264

Label

Color

State

Description

OFF (red)

No VSWR alarm is generated.

CPRI0

Red/Green

On (green)

The CPRI links are normal.

On (red)

The reception of the optical module is
abnormal, and an alarm is generated.

ON for 1s and OFF for
1s (red)

The CPRI link has a loss-of-lock error.

OFF

The SFP is out of position, or the
optical module is powered off.

CPRI1

Red/Green

On (green)

The CPRI links are normal.

On (red)

The reception of the optical module is
abnormal, and an alarm is generated.

ON for 1s and OFF for
1s (red)

The CPRI link has a loss-of-lock error.

OFF

The SFP is out of position, or the
optical module is powered off.

Ports

Table 4-51

describes the ports on the WRFU panel.

Table 4-51

Ports on the WRFU panel

Port

Label

Connector

Description

RF port

ANT_RXB

DIN

RF RX port, connected to the antenna
system

ANT_TX/
RXA

DIN

RF TX/RX port, connected to the antenna
system

CPRI

CPRI0

SFP female

Connected to the BBU, or the upper-level
WRFU during the cascading

CPRI1

SFP female

Connected to the lower-level WRFU
during the cascading

Interconnectio
n port for RF
RX signals

RX_INB

QMA female

Input port of diversity signals in the
antenna channel

RX_OUTA

QMA female

Output port of diversity signals in the
antenna channel

Power supply
socket

PWR

2V2 power

Feeding power

4 BTS3900 Components

BTS3900

Hardware Description

4-52

Huawei Proprietary and Confidential

Issue 04 (2011-02-15)

Summary of Contents for BTS3900 V100R003









































































































































































































































































Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands

Huawei BTS3900 V100R003, Hardware Description

Search results

Summary of Contents for BTS3900 V100R003

Reviews:

Related manuals for BTS3900 V100R003

Brands by name

Popular brands