Huawei AAU3902 Hardware Description Download Page 4 | Manualshive

Page: 4 / 37

background image

Organization

1 Changes in AAU3902 Hardware Description

This chapter describes changes in

AAU3902 Hardware Description

.

2 AAU Introduction

This chapter describes the AAU exteriors, functions, slot assignment, ports, indicators, RET
system, and engineering specifications.

3 AAU Cables

This chapter describes the cables connected to an AAU.

Conventions

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.

Calls attention to important information, best practices and
tips.
NOTE is used to address information not related to personal
injury, equipment damage, and environment deterioration.

General Conventions

The general conventions that may be found in this document are defined as follows.

Convention

Description

Times New Roman

Normal paragraphs are in Times New Roman.

AAU3902
Hardware Description

About This Document

Issue 06 (2014-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

iii

«
...
2
3
4
5
6
...
»

Summary of Contents for AAU3902






































Reviews:

No comments

Related manuals for AAU3902

Brand: Maclean Pages: 3

Brand: ANTARION Pages: 18

Brand: Winegard Pages: 8

Brand: Range Master Pages: 48

Brand: DX Engineering Pages: 32

Brand: Hama Pages: 38

Brand: KVH Industries Pages: 13

Brand: Datalogic Pages: 2

Brand: CommScope Pages: 2

Brand: Solid Signal Pages: 2

Brand: Leica Pages: 38

Brand: H3C Pages: 6

Brand: H3C Pages: 7

Brand: Paradigm Pages: 20

Brand: iAutoSat Pages: 42

Bernese Mountain Dog A

Brand: Parsec Technologies Pages: 20

Brand: NetComm Pages: 20

Brand: TP-Link Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands