Huawei AAU3902 Hardware Description Download Page 11 | Manualshive

Page: 11 / 37

background image

2

AAU Introduction

About This Chapter

This chapter describes the AAU exteriors, functions, slot assignment, ports, indicators, RET
system, and engineering specifications.

2.1 AAU Exterior

This section describes the exterior of an AAU and its components.

2.2 AAU Function

The function of an AAU is performed by the functional modules in it.

2.3 AAU Slot Assignment

This section describes the slot assignment of an AAU.

2.4 Ports and Indicators on an AAU

This section describes ports and indicators on an AAU.

2.5 AAU RET System

The remote electrical tilt (RET) system of an AAU consists of the remote control unit (RCU),
motor, gearing, and phase shifter. In the RET system, the RCU is used to remotely adjust the
downtilts of AU beams.

2.6 AAU Engineering Specifications

This section describes engineering specifications of an AAU, including input power and
equipment specifications.

2.7 Optical Modules

An optical module transmits optical signals between an optical port and a fiber optic cable.

AAU3902
Hardware Description

2 AAU Introduction

Issue 06 (2014-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

4

«
...
9
10
11
12
13
...
»

Summary of Contents for AAU3902






































Reviews:

No comments

Related manuals for AAU3902

Brand: Yaesu Pages: 11

Aironet AIR-ANT25-LOC-02

Brand: Cisco Pages: 28

AIR-ANT2544V4M-R

Brand: Cisco Pages: 14

AIR-ANT2451NV-R

Brand: Cisco Pages: 10

Aironet 2 dBi Diversity Omnidirectional Ceiling Mount Antenna AIR-ANT5959

Brand: Cisco Pages: 8

Aironet AIR-ANT2012

Brand: Cisco Pages: 6

Brand: Cisco Pages: 8

Aironet AIR-ANT2506

Brand: Cisco Pages: 8

Brand: Cisco Pages: 16

Brand: Cisco Pages: 535

Aironet 2 dBi Diversity Omnidirectional Ceiling Mount Antenna AIR-ANT5959

Brand: Cisco Pages: 29

Aironet AIR-ANT2513P4M-N

Brand: Cisco Pages: 14

Aironet AIR-ANT5114P2M-N

Brand: Cisco Pages: 14

Brand: Cisco Pages: 4

Aironet AIR-ANT2566D4M-R

Brand: Cisco Pages: 18

Aironet AIR-ANT5160V-R

Brand: Cisco Pages: 10

Aironet AIR-ANT5140V-R

Brand: Cisco Pages: 12

Aironet AIR-ANT2414S-R

Brand: Cisco Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands