Huawei AAU3902 Hardware Description Download Page 27 | Manualshive

Page: 27 / 37

background image

3

AAU Cables

About This Chapter

This chapter describes the cables connected to an AAU.

3.1 List of AAU Cables

The cable list provides reference for cable installation and replacement.

3.2 AAU PGND Cable

A PGND cable connects an AAU and a ground bar for proper grounding of the AAU. The
maximum length of an AAU PGND cable is 8 m (26.25 ft).

3.3 AAU Power Cable

An AAU power cable feeds external -48 V DC power into an AAU. The maximum length of an
AAU power cable between the AAU and its power supply is 100 m (328.08 ft).

3.4 CPRI Fiber Optic Cable

CPRI fiber optic cables are classified into multimode fiber optic cables and single-mode fiber
optic cables. They transmit CPRI signals.

3.5 (Optional) Cascading CPRI Fiber Optic Cable

Cascading CPRI fiber optic cables are classified into multimode fiber optic cables and single-
mode fiber optic cables. They transmit CPRI signals.

A feeder connects an RRU and an AAU and transmits signals between the base station and the
antenna system.

3.7 AISG Multi-Wire Cable

An AISG multi-wire cable connects an RRU and an AAU to transmit control signals from a base
station to an RET antenna. When the RRU is connected to the RET antenna, an AISG multi-
wire cable transmits RS485 signals. The length of an AISG multi-wire cable is 5 m (16.40 ft).

3.8 AISG Extension Cable

When the distance between an RRU and an AAU is longer than 5 m (16.4 ft), an AISG multi-
wire cable is not long enough to connect the RRU and the AAU. In this case, an AISG extension
cable is used to extend the AISG multi-wire cable. An AISG extension cable is 15 m (49.21 ft).

AAU3902
Hardware Description

3 AAU Cables

Issue 06 (2014-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

20

«
...
25
26
27
28
29
...
»

Summary of Contents for AAU3902






































Reviews:

No comments

Related manuals for AAU3902

Brand: One for All Pages: 2

Super Cantenna SCB10X

Brand: Wireless Garden Pages: 13

ProCurve J9169A

Brand: HP Pages: 4

ProCurve J8444A

Brand: HP Pages: 2

ProCurve J8445A

Brand: HP Pages: 2

SIMCom SIM8200G

Brand: Sunsea AIoT Pages: 26

Brand: Greyline Pages: 4

Brand: YIC Technologies Pages: 7

Brand: Blake UK Pages: 2

Oyster SAT-DOM 50 GS

Brand: Ten-Haaft Pages: 20

Brand: Ten-Haaft Pages: 44

Brand: Ten Haft Pages: 75

samy solar plus

Brand: Ten-Haaft Pages: 128

Brand: PRO.SIS.TEL. Pages: 4

Brand: PRO.SIS.TEL. Pages: 4

Brand: PRO.SIS.TEL. Pages: 7

Brand: Hy-Gain Pages: 3

Brand: Hy-Gain Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands