HUALIAN FRM-980I Manual Download Page 1

Page: 1 / 32

Contents

................................................................................................................................................ 1

1 Product Introduction

................................................................................................................... 2

1.1 Products’ application

.................................................................................................................... 2

1.2 Products’ feature

....................................................................................................................... 2

1.3 Operation principles

................................................................................................................. 2

1.4 Principles of products’ naming

................................................................................................ 3

1.5 Parameters of products

............................................................................................................ 3

1.6 Products’ external structures

.................................................................................................. 4

2 Safety, Preparation and Examination

....................................................................................... 8

2.1 Preparation for use

................................................................................................................... 8

2.2 Precautions on safety

............................................................................................................... 8

2.3 Operational environment

......................................................................................................... 9

3 Installation

..................................................................................................................................... 9

3.1 Necessary conditions for installation

..................................................................................... 9

3.2 Installation environment

.......................................................................................................... 9

3.3 Installation steps

....................................................................................................................... 9

4 Startup and Commissioning

...................................................................................................... 13

4.1 Introduction to the controlling panel

................................................................................... 13

4.2 Power on

................................................................................................................................... 13

4.3 Commissioning

......................................................................................................................... 16

5 Standard Operation & Parameter Setting

.............................................................................. 24

5.1 Preparation, adjustment and inspection before operation

.............................................. 25

5.2 Parameter setting

.................................................................................................................... 25

6 Maintenance

............................................................................................................................... 26

6.1 Attention for maintenance

.................................................................................................... 26

6.2 Maintenance schedule

........................................................................................................... 27

7 Troubleshooting

.......................................................................................................................... 27

7.1 Troubleshooting

...................................................................................................................... 27

7.2 Motor maintenance

................................................................................................................ 29

8 Movement and Storage

............................................................................................................. 30

8.1 Equipped with carton packaging

........................................................................................... 30

8.2 Storage of short time

.............................................................................................................. 30

8.3 Storage of long time

................................................................................................................ 30

8.5 Start the machine after long-term storage

.......................................................................... 30

9 Electric Schematic Diagram

...................................................................................................... 31

9.1 Electric schematic diagram

.................................................................................................... 31

Summary of Contents for FRM-980I

































Search results

Summary of Contents for FRM-980I

Reviews:

Related manuals for FRM-980I

Brands by name

Popular brands

HUALIAN FRM-980I, Manual

Search results

Summary of Contents for FRM-980I

Reviews:

Related manuals for FRM-980I

Brands by name

Popular brands