HTP SS-26-FP Installation, Start-Up, Maintenance, Parts, Warranty Download

Page: 1 / 20

Flat Plate

Solar Collectors

Installation

Start-Up

Maintenance

Parts

Warranty

For Residential and Commercial Use

SS-26-FP / SS-32-FP / SS-40-FP Models*

*“FP” Denotes Smooth Copper Tube w/ Aluminum Plate Models
“U” Denotes Model with Unions
“W” Denotes Model with Sensor Wells

This manual must only be used by a qualified installer / service technician. Read all instructions in this manual before installing.

Perform steps in the given order. Failure to do so could result in substantial property damage, severe personal injury, or death.

HTP reserves the right to make product changes or updates without notice and will not be held liable for typographical errors

in literature.

The surfaces of these products contacted by potable (consumable) water contain less than 0.25% lead by weight as required

by the Safe Drinking Water Act, Section 1417.

NOTE TO CONSUMER: PLEASE KEEP ALL INSTRUCTIONS FOR FUTURE REFERENCE.

272 Duchaine Blvd.

New Bedford, MA 02745

www.htproducts.com

lp-364 Rev. 000 Rel. 007 Date 2.12.18

Summary of Contents for SS-26-FP





















Search results

Summary of Contents for SS-26-FP

Reviews:

Related manuals for SS-26-FP

Brands by name

Popular brands

HTP SS-26-FP, Installation, Start-Up, Maintenance, Parts, Warranty

Search results

Summary of Contents for SS-26-FP

Reviews:

Related manuals for SS-26-FP

Brands by name

Popular brands