background image

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

63

MODCON Boiler

 

Limited Warranty

Ten year warranty to assure your complete satisfaction.

HTP warrants this boiler and its components to be free from 

defects in material and workmanship according to the following 

terms, conditions, and time periods.

 

UNLESS OTHERWISE NOTED 

THESE WARRANTIES COMMENCE ON THE DATE OF INSTALLATION. 

This limited warranty is only available to the 

original consumer 

purchaser 

(herinafter “Owner”) of this boiler, and is non-transferable.

COVERAGE

A. During the first year after the date of installation, HTP warrants 

that it will repair or replace, at its option, any defective or 

malfunctioning component of the boiler that is found to have failed 

due to manufacturer’s defect. Replacement components will be 

warranted for ninety (90) days. No other component of the boiler will 

be replaced after this period (with exception to the blower motor, 

which will have a limited warranty of three [3] years). 

B. During the first through fifth year after the date of installation, should 

a defect or malfunction result in a leakage of water from the boiler 

due to defective material or workmanship, malfunction, or failure to 

comply with the above warranty, with such defect or malfunction 

having been verified by an authorized HTP representative, HTP will 

repair or replace, at its option, the defective or malfunctioning boiler. 

Replacements will be of the nearest comparable model available at 

the time of replacement. The replacement boiler will be warranted 

for the unexpired portion of the applicable warranty period of the 

original boiler.

C. During the sixth through tenth year after the date of installation, 

should a defect or malfunction result in a leakage of water from 

the boiler due to defective material or workmanship, malfunction, 

or failure to comply with the above warranty, with such defect 

or malfunction having been verified by an authorized HTP 

representative, HTP will repair or replace, at its option, the defective 

or malfunctioning boiler at a cost to the Owner equal to the following 

percentages of the manufacturer’s list price in effect at the date of 

replacement: 

Year of Claim

6

7

8

9

10

Percentage to be Paid 

by Purchaser

50 %

60 %

70%

80 %

90 %

Replacements will be of the nearest comparable model available at 

the time of replacement. The replacement boiler will be warranted 

for the unexpired portion of the applicable warranty period of the 

original boiler.

D. In the event of a leakage of water of a replacement boiler due 

to defective material or workmanship, malfunction, or failure to 

comply with the above warranty, HTP reserves the right to refund 

to the Owner the published wholesale price available at the date of 

manufacture of the original boiler.

E. If government regulations, industry certification, or similar 

standards require the replacement boiler or component(s) to have 

features not found in the defective boiler or component(s), the Owner 

will be charged the difference in price represented by those required 

features. If the Owner pays the price difference for those required 

features and/or to upgrade the size and/or other features available 

on a new replacement boiler or component(s), the Owner will also 

receive a complete new limited warranty for that replacement boiler 

or component(s).

F. If at the time of a request for service the Owner cannot provide 

a copy of the original sales receipt or the warranty registration, 

the warranty period for the boiler shall then be deemed to have 

commenced thirty (30) days after the date of manufacture of the 

boiler and NOT the date of installation of the boiler, and be covered 

by the unexpired portion of the warranty detailed above.

G. This warranty extends only to boilers utilized in closed loop 

heating applications that have been properly installed based upon 

the manufacturer’s installation instructions.

H. It is expressly agreed between HTP and the Owner that repair, 

replacement, or refund are the exclusive remedies of the Owner.

OWNER RESPONSIBILITIES

The Owner or Qualified Installer / Service Technician must:

1. Have a relief valve bearing the listing marks of the American Society 

of Mechanical Engineers (ASME) installed with the boiler assembly in 

accordance with federal, state, and local codes.

2. Maintain the boiler in accordance with the maintenance procedure 

listed in the manufacturer’s provided instructions. Preventive 

maintenance can help avoid any unnecessary breakdown of the 

boiler and keep it running at optimum efficiency.

3. Maintain all related system components in good operating 

condition. 

4. Check all condensate lines to confirm that all condensate drains 

properly from the boiler.

5. Use the boiler in a closed system with a properly sized and installed 

thermal expansion tank.

6. Use the boiler at water pressures not exceeding the working 

pressure shown on the rating plate.

7. Keep the boiler free of damaging scale deposits.

8. Make provisions so if the boiler or any component or connection 

thereto should leak, the resulting flow of water will not cause damage 

to the area in which it is installed.

WARRANTY EXCLUSIONS

This limited warranty will not cover:

1. Any boiler purchased from an unauthorized dealer.

2. Any boiler not installed by a qualified heating installer/service 

technician, or installations that do not conform to ANSI, CSA, and/

or UL standards, as well as any applicable national or local building 

codes.

3. Service trips to teach the Owner how to install, use, maintain, or 

to bring the boiler installation into compliance with local building 

codes and regulations.

4. The workmanship of any installer. The manufacturer disclaims 

and does not assume any liability of any nature caused by improper 

installation, repair, or maintenance.

5. Electricity or fuel costs, or increased or unrealized savings for same, 

for any reason whatsoever.

6. Any water damage arising, directly or indirectly, from any defect in 

the boiler or component part(s) or from its use.

7. Any incidental, consequential, special, or contingent damages or 

expenses arising, directly or indirectly, from any defect in the boiler 

or the use of the boiler.

8. 

Failure to locate the boiler in an area where leakage of the boiler or 

water line connections and the relief valve will not result in damage to 

the area adjacent to the boiler or lower floors of the structure, as well 

as failure to install the boiler with properly designed containment 

measures.

9. Any failed components of the system not manufactured by HTP as 

part of the boiler.

10. Boilers repaired or altered without the prior written approval of 

HTP.

11. Damages, malfunctions, or failures resulting from failure to install 

the boiler in accordance with applicable building codes/ordinances 

or good plumbing and electrical trade practices. 

12. Damages, malfunctions, or failures resulting from improper 

installation, failure to operate the boiler at firing rates or pressures 

not exceeding those on the rating plate, or failure to operate and 

maintain the boiler in accordance with the manufacturer’s provided 

instructions.

13. Failure to operate the boiler in a closed system with a properly 

Summary of Contents for MODCON500 FS



































































Reviews: