HTP MODCON500 FS Page 2 Installation, Start-Up, Maintenance, Parts, Warranty Download

Page: 2 / 66

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal

injury or death.

•

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the fire department.

•

Installation and service must be provided by a qualified installer, service agency or the gas supplier.

Improper installation, adjustment, alteration, service, or maintenance can cause injury, property damage, or death. Refer to this

manual. Installation and service must be performed by a qualified installer, service agency, or gas supplier.

Summary of Contents for MODCON500 FS



































































Search results

Summary of Contents for MODCON500 FS

Reviews:

Related manuals for MODCON500 FS

Brands by name

Popular brands

HTP MODCON500 FS, Installation, Start-Up, Maintenance, Parts, Warranty

Search results

Summary of Contents for MODCON500 FS

Reviews:

Related manuals for MODCON500 FS

Brands by name

Popular brands