manualshive.com logo in svg

HTP MODCON500 FS, Installation, Start-Up, Maintenance, Parts, Warranty

Share
Download
HTP MODCON500 FS Installation, Start-Up, Maintenance, Parts, Warranty Download Page 27

lp-445-r4 Rev. 006 Rel. 027 Date 7.21.20

27

All vent pipes must be glued, properly supported, and the exhaust 

pitched a minimum of 1/4” per foot back to the boiler to allow 

drainage of condensate. When placing support brackets on vent 

piping, the first bracket must be within 1 foot of the boiler and the 

balance of 4 foot intervals on the vent pipe. Venting must be readily 

accessible for visual inspection from the first three feet from the 

boiler.

NOTE: 

These drawings are meant to demonstrate system venting only. 

The installer is responsible for all equipment and detailing required by 

local codes.

Ensure the terminations are screened to prevent blockage caused by 

debris or birds.

Figure 15 - Unbalanced Venting - Roof Exhaust and Sidewall Intake

An unbalanced vent system can be installed ONLY when the exhaust 

is in the vertical position. Failure to do so could result in serious 

personal injury or death.

Figure 16 - Roof and Sidewall Venting with Stainless Steel

Take extra precaution to adequately support the weight of vent 

pipes terminating through the roof. Failure to properly support roof 

terminated vent piping could result in property damage, serious 

personal injury, or death due to flue gas leakage.

Summary of Contents for MODCON500 FS



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands