manualshive.com logo in svg

HPE SimpliVity 2600 Gen10, Installation And Maintenance Manual

Share
Download
HPE SimpliVity 2600 Gen10 Installation And Maintenance Manual Download Page 22

Chapter 4: Server troubleshooting

22

Chapter 4: Server troubleshooting

This section contains the following topics:

•

Diagnostic indicators

•

Drive monitoring

•

Power supply monitoring

•

Network interface monitoring

You can use the diagnostic indicators and LEDs to identify problems with the server hardware. For assistance

with resolving hardware problems, such as a component failing, contact 

Customer Support (support.hpe.com)

.

Diagnostic indicators

The front panel on the HPE SimpliVity 2600 Gen10 chassis provides diagnostic LEDs that indicate when each

server is functioning properly and when a hardware-related error occurs. The indicators can help you correct

problems before they affect service levels.

Callout

Function

LED

State

Solid green

Normal operation

Flashing green ILO is rebooting

1

Health LED (for

each server)

Flashing amber System degraded

Summary of Contents for SimpliVity 2600 Gen10






































Reviews:

No comments

Brands by name

Popular brands

Load more brands