HPE ProLiant DL388 Gen10 Maintenance And Service Manual Download Page 158 | Manualshive

Page: 158 / 169

background image

Power supply specifications

Depending on the installed options and the regional location where the server was purchased, the server can
be configured with one of the following power supplies:

•

HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply

on page 158

•

HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply

on page 159

•

HPE 800W Flex Slot Titanium Hot Plug Low Halogen Power Supply

on page 160

•

HPE 800W Flex Slot Universal Hot Plug Low Halogen Power Supply

•

HPE 800W Flex Slot -48VDC Hot Plug Low Halogen Power Supply

on page 161

•

HPE 800W Flex Slot Scalable Persistent Memory Power Supply

•

HPE 1600W Flex Slot Platinum Hot Plug Low Halogen Power Supply

For detailed power supply specifications, see the QuickSpecs on the

Hewlett Packard Enterprise website

.

HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply

Specification

Value

Input requirements

Rated input voltage

100 VAC to 127 VAC

100 VAC to 240 VAC

240 VDC for China only

Rated input frequency

50 Hz to 60 Hz

Not applicable to 240 VDC

Rated input current

5.8 A at 100 VAC

2.8 A at 200 VAC

2.4 A at 240 VDC for China only

Maximum rated input power

557 W at 100 VAC

539 W at 200 VAC

537 W at 240 VDC for China only

BTUs per hour

1,902 at 100 VAC

1,840 at 200 VAC

1,832 at 240 VDC for China only

Power supply output

Table Continued

158

Specifications

«
...
156
157
158
159
160
...
»

Summary of Contents for ProLiant DL388 Gen10










































































































































































Reviews:

No comments

Related manuals for ProLiant DL388 Gen10

ColorPASS-Z5000

Brand: Canon Pages: 134

Express5800/320Ma

Brand: NEC Pages: 80

Express5800/320Ma

Brand: NEC Pages: 90

Brand: Z Microsystems Pages: 17

Brand: Wyse Pages: 6

Brand: Xblue Networks Pages: 42

RIP Station 5100

Brand: Epson Pages: 140

Brand: Brother Pages: 103

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

UCS 6400 Series

Brand: Cisco Pages: 68

Smart Storage NSS322

Brand: Cisco Pages: 2

Brand: AXIOMTEK Pages: 45

ReadiManagerSE200

Brand: Polycom Pages: 4

Brand: Terra Pages: 157

Brand: Vlinx Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands