HPE Edgeline EL300 Setup And Configuration Manual Download Page 9

Page: 9 / 91

Setup and configuration

Checklist

Complete this checklist to set up, install, and configure your new HPE Edgeline EL300 Converged Edge System.

Unbox the system and

identify the components.

Verify that the intended installation site conforms to space, airflow, temperature, and power requirements.

Install applicable hardware options:

•

Power adapter

•

8 GB SD card kit

•

SFF to M.2 drive cage kit

•

SATA/M.2 drive

Install wireless network kits and antennas:

•

HPE EL Network WiFi card

•

WiFi antenna

•

HPE EL Network LTE card

•

LTE antenna

Mount the system:

•

Wall mounting

•

DIN rail mounting

•

Base only bracket kit

•

Standard bracket kit

Prepare to configure the system:

a. Verify OS support.

b. Gather OS installation media and necessary keys.

c. Verify network connectivity.

d. Plan for network address.

Connect to the iSM and configure the system using one of the available methods:

•

Connect using the WiFi Access Point.

•

Connect to the iSM web interface.

•

Connect to the iSM CLI using serial cable.

Complete the system network configuration and install an OS.

Setup and configuration

Summary of Contents for Edgeline EL300




























































































Search results

Summary of Contents for Edgeline EL300

Reviews:

Related manuals for Edgeline EL300

Brands by name

Popular brands

HPE Edgeline EL300, Setup And Configuration Manual

Search results

Summary of Contents for Edgeline EL300

Reviews:

Related manuals for Edgeline EL300

Brands by name

Popular brands