manualshive.com logo in svg

HPE Edgeline EL300, Setup And Configuration Manual

Share
Download
HPE Edgeline EL300 Setup And Configuration Manual Download Page 25

11. Install the M.2 SSD module.

12. Install the drive cage cover.

13. Install the security cover.

14. Do one of the following:

•

Mount the system on wall.

•

Mount the system on rails.

15. Connect the power cord to the system.

16. Connect the power cord to the power source.

17. Power up the system.

The installation is complete.

M.2 device option

The first M.2 device is preinstalled in the HPE Edgeline EL300 Converged Edge System. Additional M.2 devices can be
installed using the SFF to M.2 adapter.

Installing an M.2 device

NOTE: The M.2 SSD installed on the drive cage does not have any activity LED associated.

Prerequisites

Before you perform this procedure, make sure that you have the following items available:

• M.2 device (SSD module or HPE Edgeline VPU module with Myriad X)

• Hex nut screwdriver

Hardware options installation

25

Summary of Contents for Edgeline EL300




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands