manualshive.com logo in svg

HPE Edgeline EL300, Setup And Configuration Manual

Share
Download
HPE Edgeline EL300 Setup And Configuration Manual Download Page 4

Installing the base only bracket option................................................................................................................................... 37

Standard bracket option kit.............................................................................................................................................................................38

Installing the standard bracket option.....................................................................................................................................39

Wall mounting option kit.....................................................................................................................................................................................................40

Installing the wall mounting kit..................................................................................................................................................................... 40

DIN rail mounting panel option kit................................................................................................................................................................................42

Installing the rail mounting kit....................................................................................................................................................................... 42

Associated hardware procedures...................................................................................... 47

Installing the power supply............................................................................................................................................................................................... 47
Powering up the system......................................................................................................................................................................................................47
Powering down the system............................................................................................................................................................................................... 47
Mounting the system............................................................................................................................................................................................................ 47
Dismounting the system..................................................................................................................................................................................................... 48

Dismount the system from a wall mount panel....................................................................................................................................48
Dismount the system from a rail mount panel..................................................................................................................................... 48

Removing the antenna......................................................................................................................................................................................................... 49
Removing the brackets........................................................................................................................................................................................................ 50
Removing the security cover............................................................................................................................................................................................51
Installing the security cover.............................................................................................................................................................................................. 52
Removing the drive cage cover.......................................................................................................................................................................................54
Installing the drive cage cover.........................................................................................................................................................................................55
Removing the heatspreader..............................................................................................................................................................................................56
Installing the heatspreader................................................................................................................................................................................................57

Configuration.........................................................................................................................59

Quick task: Be prepared.......................................................................................................................................................................................................59

Prepare for configuration..................................................................................................................................................................................59

Connecting to HPE iSM the first time..........................................................................................................................................................................59

Connecting to the iSM web interface using the WiFi Access Point..........................................................................................60
Connecting to the iSM web interface using Ethernet.......................................................................................................................60
Connecting to the iSM CLI in a serial session........................................................................................................................................61

iSM web interface....................................................................................................................................................................................................................61

Configuring the Internet Explorer JavaScript setting...................................................................................................................... 62
Logging in to the iSM web interface...........................................................................................................................................................62
About the iSM web interface controls....................................................................................................................................................... 63

Quick task: Configure the network connection and install an operating system...............................................................................63

Complete the network configuration using Integrated System Manager and install an operating system.....63

iSM Network Port-Network Summary.........................................................................................................................................................................64

Viewing the network configuration summary.......................................................................................................................................65

Network configuration summary details................................................................................................................................ 65
IPv4 Summary details........................................................................................................................................................................65
IPv6 Summary details........................................................................................................................................................................66
WiFi Summary details........................................................................................................................................................................ 66
LTE Summary details.........................................................................................................................................................................66

Configuring Host Name Settings..................................................................................................................................................................66

iSM host name and domain name limitations......................................................................................................................67

Configuring IPv4 settings................................................................................................................................................................................. 67

DHCPv4 Configuration setting.................................................................................................................................................... 67
Static IPv4 Address Configuration settings..........................................................................................................................68

Configuring IPv6 settings................................................................................................................................................................................. 68

IPv6 Configuration settings........................................................................................................................................................... 68

Configuring WiFi settings ................................................................................................................................................................................ 69
Configuring WiFi Access Point settings....................................................................................................................................................70

4

Summary of Contents for Edgeline EL300




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands