manualshive.com logo in svg

HP X5000 G2, Administrator'S Manual

Share
Download
HP X5000 G2 Administrator'S Manual Download Page 162

off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit that is different from that to which the receiver
is connected.

•

Consult the dealer or an experienced radio or television technician for help.

Modification

The FCC requires the user to be notified that any changes or modifications made to this device
that are not expressly approved by Hewlett-Packard Company may void the user's authority to
operate the equipment.

Cables

When provided, connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods in order to maintain compliance with FCC Rules and Regulations.

Canadian notice (Avis Canadien)

Class A equipment

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la class A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

Class B equipment

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la class B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

European Union notice

This product complies with the following EU directives:

•

Low Voltage Directive 2006/95/EC

•

EMC Directive 2004/108/EC

Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard
for this product or product family.
This compliance is indicated by the following conformity marking placed on the product:

This marking is valid for non-Telecom products and EU
harmonized Telecom products (e.g., Bluetooth).

Certificates can be obtained from

http://www.hp.com/go/certificates

.

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany

162

Regulatory compliance notices

Summary of Contents for X5000 G2




















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands