HP VSR1000 Configuration Manual Download Page 326

Page: 326 / 463

314

Configure BFD over the path. Then if the path fails, BFD can quickly detect the failure and notify it to IPv6

BGP. Then the path Router A<—>Router D<—>Router C takes effect immediately.

Figure 75

Network diagram

Configuration procedure

Configure IPv6 addresses for interfaces. (Details not shown.)

Configure OSPFv3 so that Router A and Router C can reach each other. (Details not shown.)

Configure IPv6 BGP on Router A:
# Establish two IBGP connections to Router C.

<RouterA> system-view

[RouterA] bgp 200

[RouterA-bgp] router-id 1.1.1.1

[RouterA-bgp] peer 2002::2 as-number 200

[RouterA-bgp] peer 3002::2 as-number 200

[RouterA-bgp] address-family ipv6

[RouterA-bgp-ipv6] peer 2002::2 enable

[RouterA-bgp-ipv6] peer 3002::2 enable

[RouterA-bgp-ipv6] quit

# Create IPv6 ACL 2000 to permit 1200::0/64 to pass.

[RouterA] acl ipv6 number 2000

[RouterA-acl6-basic-2000] rule permit source 1200:: 64

[RouterA-acl6-basic-2000] quit

# Create two routing policies to set the MED for route 1200::0/64. The policy

apply_med_50

sets

the MED to 50, and the policy

apply_med_100

sets the MED to 100.

[RouterA] route-policy apply_med_50 permit node 10

[RouterA-route-policy-apply_med_50-10] if-match ipv6 address acl 2000

[RouterA-route-policy-apply_med_50-10] apply cost 50

[RouterA-route-policy-apply_med_50-10] quit

[RouterA] route-policy apply_med_100 permit node 10

[RouterA-route-policy-apply_med_100-10] if-match ipv6 address acl 2000

[RouterA-route-policy-apply_med_100-10] apply cost 100

[RouterA-route-policy-apply_med_100-10] quit

GE1/0

2001::1/64

GE2/0
2002::2/64

Router A

Router C

AS 200

Router D

GE1/0

2001::2/64

GE2/0
2002::1/64

GE2/0

3001::1/64

GE2/0

3001::2/64

GE1/0
3002::1/64

GE1/0
3002::2/64

Router B

AS 100

AS 300

1200::0/64

Summary of Contents for VSR1000
















































































































































































































































































































































































































































































Search results

Summary of Contents for VSR1000

Reviews:

Related manuals for VSR1000

Brands by name

Popular brands

HP VSR1000, Configuration Manual

Search results

Summary of Contents for VSR1000

Reviews:

Related manuals for VSR1000

Brands by name

Popular brands