HP R3000v User Manual Download Page 43

Page: 43 / 98

SPECIFICATIONS

HP R3000v UPS User Guide

164201731 Rev 1

Table 8

Environmental and Safety

Surge Suppression

IEC/EN 61004-5

EMC Certifications

IEC/EN 62040-2, Emissions: Category C2, Immunity: Category C2

EMC (Emissions)

IEC 62040-2:ed2:2005; EN 62040-2:2006

Safety Conformance

IEC 62040-1-1

Operating Temperature

0°C to 40°C (32°F to 104°F) in Online mode, with linear derating for altitude

NOTE: Thermal protection switches load to bypass in case of overheating.

Storage Temperature

-20°C to 40°C (-4°F to 104°F) with batteries

-25°C to 55°C (-13°F to 131°F) without batteries

Transit Temperature

-25°C to 55°C (-13°F to 131°F)

Relative Humidity

5–90% noncondensing

Operating Altitude

Up to 3,000 meters (9,843 ft) above sea level

Transit Altitude

Up to 10,000 meters (32,808 ft) above sea level

Audible Noise

<50 dBA at 1 meter typical

Leakage Current

<1.5 mA

Table 9

Battery Runtimes (in Minutes) at 100% Load

Model

Internal Batteries

+ 1 ERM

+ 2 ERMs

+ 3 ERMs

+ 4 ERMs

HP R3000v UPS

Table 10

Battery

Internal Batteries

Extended Runtime Modules

Configuration

72 Vdc (6 12V, 9 Ah)

HP R3000v ERM: 72 Vdc (2x6 12V, 9 Ah)

Fuses

Not applicable

(4) 30A/125 Vdc fuses per ERM

Type

Sealed, maintenance-free, valve-regulated, lead-acid, with minimum 3-year float service life at 25°C (77°F)

Monitoring

Advanced monitoring for earlier failure detection and warning

Recharge Time

3 hours to 90%

Battery Port

External three-pole Anderson connector on UPS for connection to ERM

Summary of Contents for R3000v



































































































Search results

Summary of Contents for R3000v

Reviews:

Related manuals for R3000v

Brands by name

Popular brands

HP R3000v, User Manual

Search results

Summary of Contents for R3000v

Reviews:

Related manuals for R3000v

Brands by name

Popular brands