manualshive.com logo in svg

HP ProLiant DL320 Generation 5p, User Manual

Share
Download
HP ProLiant DL320 Generation 5p User Manual Download Page 18

 

Component identification  18 

System LED and 
Color 

Internal Health 
LED Color 

Status 

 

Amber 

•

 

DIMM in slot 

X

 has reached single-bit correctable error 

threshold. 

•

 

DIMM in slot 

X

 is in a pre-failure condition. 

•

 

DIMM in slot 

X

 is an unsupported type, but valid 

memory exists in another bank. 

DIMM failure, all slots 
in one bank (amber) 

Red 

No valid or usable memory is installed in the system. 

Overtemperature 

(amber) 

Amber 

The Health Driver has detected a cautionary temperature 

level. 

 

Red 

The server has detected a hardware critical temperature 

level. 

Fan module (red) 

Red 

The minimum fan requirements are not being met in one or 
more of the fan modules. One or more fans have failed or 

are missing. 

Power supply signal 
interlock (amber) 

Red 

The power supply signal cable is not connected to the 
system board. 

 

 

Internal USB connector 

 

For more information, see "Internal USB functionality (on page 

61

)." 

 

Summary of Contents for ProLiant DL320 Generation 5p











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands