HP ProDesk 600 G1 Tower Hardware Reference Manual Download Page 8

Page: 8 / 33

Front panel components

Drive configuration may vary by model. Some models have a bezel blank covering one or more drive
bays.

Dual-State Power Button

USB 3.0 Port - Charging

Hard Drive Activity Light

Microphone/Headphone Connector

USB 3.0 Port

Headphone Connector

NOTE:

The USB 3.0 Port - Charging also provides current to charge a device such as a Smart Phone. The

charging current is available whenever the power cord is plugged into the system, even when the system is off.

NOTE:

When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if

you want to use the connector for a microphone Line-In device or a headphone. You can reconfigure the
connector at any time by double-clicking the Audio Manager icon in the Windows taskbar.

NOTE:

The Power On Light is normally white when the power is on. If it is flashing red, there is a problem with

the computer and it is displaying a diagnostic code. Refer to the

Maintenance and Service Guide

to interpret the

code.

Chapter 1 Product features

Summary of Contents for ProDesk 600 G1 Tower


































Search results

Summary of Contents for ProDesk 600 G1 Tower

Reviews:

Related manuals for ProDesk 600 G1 Tower

Brands by name

Popular brands

HP ProDesk 600 G1 Tower, Hardware Reference Manual

Search results

Summary of Contents for ProDesk 600 G1 Tower

Reviews:

Related manuals for ProDesk 600 G1 Tower

Brands by name

Popular brands