HP Performance Optimized Datacenter 20c Maintenance And Service Manual Download Page 17 | Manualshive

Page: 17 / 88

background image

Illustrated parts catalog 17

Spare part number Description

660804-001

SPS-Measurement Terminal

660805-001

SPS-Relay Assembly

660806-001

SPS-Relay Assembly

660807-001

SPS-Relay Assembly

660808-001

SPS-Breaker

660809-001

SPS-Breaker

660810-001

SPS-Power Supply QUINT-PS/1AC/24DC/20

660811-001

SPS-Pwr Sup QUINT-ORING/24DC/2X20/1X40

660812-001

SPS-Power Supply UPS-20A

660817-001

SPS-RELAY RM35LM33MW

660820-001

SPS-RELAY 072.11

660822-001

SPS-SWITCH VCF2 40A

The component part in the following table must be replaced by an authorized fire safety technician.

IMPORTANT:

These parts must be replaced by a licensed fire safety contractor according to all

local and regional fire codes, and in compliance with manufacturer specifications.

Spare part number Description

664746-001

SPS-DETECTOR SMOKE VESDA VLS 214

Installation considerations

CAUTION:

All plumbing to and from the HP POD 20c must be completed by a licensed plumber.

All wiring in and around the HP POD 20c must be completed by a licensed electrician. Failure to
comply with these instructions can impact your warranty and/or result in equipment damage.

Safety and IEC compliance

The HP POD 20c is examined, tested, and found to be in compliance with IEC/EN 60950 Part 1 and Part

22 as an Information Technology Product. For more information, see "HP POD 20c regulatory compliance
(on page

)."

The HP POD 20c is not suitable for long-term human occupancy. The HP POD 20c is Listed as a Product that

provides service access areas for periodic maintenance and service. These areas must be used only by

owner-authorized and qualified personnel who are trained in the maintenance and service of the HP POD
20c components.

IMPORTANT:

Before installing the HP POD 20c, consult your local Authorities for applicable

regulations and to review site-specific location guidelines. If needed, obtain any necessary

permits.

Additional considerations for safety and Electrical compliance are as follows:

•

The HP POD 20c is Certified as an Information Technology Product to IEC/EN 60950 Part 1 and Part
22.

•

The HP POD 20c is evaluated as a "non-inhabitable product" that provides "service access" areas for
customer-authorized, qualified, and trained service personnel.

«
...
15
16
17
18
19
...
»

Summary of Contents for Performance Optimized Datacenter 20c

























































































Reviews:

No comments

Related manuals for Performance Optimized Datacenter 20c

Brand: Deuba Pages: 7

Brand: CASARIA Pages: 13

Brand: Husky Pages: 10

Brand: ioSafe Pages: 4

Brand: Hama Pages: 8

Brand: Quantum Pages: 344

Brand: NCR Pages: 12

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 8

FZ-VSD55 Series

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 4

FZ-VSD40 Series

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands