HP P6116f - Pavilion - 8 GB RAM Supplementary Manual Download

Page: 4 / 50

570981-001

— Removing and Replacing the Front Panel

Before You Begin

Observe the following requirements before removing and
replacing the front panel.

Removing the Front Panel

Remove the Pocket Media Drive, if it is present.

Turn off the computer.

Disconnect all peripherals and cables from the front
and the back of the computer. Disconnect the power
cord last.

Tools Needed

Flathead screwdriver

You can use a flathead screwdriver with the
following screw (torque screw).

CAUTION:

Static electricity can damage

the electronic components inside the
computer. Discharge static electricity by
touching the metal cage of the computer
before touching any internal parts or
electronic components.

WARNING:

Never open the cover with the
power cord attached or power
applied. You may damage your
computer or be injured from the
spinning fan blades.

Avoid touching sharp edges
inside the computer.

NOTE:

Computer features may vary by model.

Removing and Replacing the Front Panel

10–20 minutes

Summary of Contents for P6116f - Pavilion - 8 GB RAM


















































Search results

Summary of Contents for P6116f - Pavilion - 8 GB RAM

Reviews:

Related manuals for P6116f - Pavilion - 8 GB RAM

Brands by name

Popular brands

HP P6116f - Pavilion - 8 GB RAM, Supplementary Manual

Search results

Summary of Contents for P6116f - Pavilion - 8 GB RAM

Reviews:

Related manuals for P6116f - Pavilion - 8 GB RAM

Brands by name

Popular brands