manualshive.com logo in svg

HP P6116f - Pavilion - 8 GB RAM, Supplementary Manual

Share
Download
HP P6116f - Pavilion - 8 GB RAM Supplementary Manual Download Page 10

2

537487-001

— Removing and Replacing an Optical Disc Drive

Before You Begin

Observe the following requirements before removing and 
replacing the optical disc drive. 

Removing an Optical Disc Drive

1

Before you begin servicing the computer, press the 
Eject button, and remove any CD or DVD from the 
optical disc drive tray.

Tools Needed

Flathead screwdriver

You can use a flathead screwdriver with the 
following screw (torque screw).

CAUTION: 

Static electricity can damage 

the electronic components inside the 
computer. Discharge static electricity by 
touching the metal cage of the computer 
before touching any internal parts or 
electronic components.

WARNING: 

Never open the cover with the 
power cord attached or power 
applied. You may damage your 
computer or be injured from the 
spinning fan blades. 

Avoid touching sharp edges 
inside the computer.

NOTE: 

Computer features may vary by model.

Removing and Replacing an Optical Disc Drive

15–25 minutes

Summary of Contents for P6116f - Pavilion - 8 GB RAM



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands