manualshive.com logo in svg

HP Model 744 - VME Workstation, Installation And Service Manual

Share
Download
HP Model 744 - VME Workstation Installation And Service Manual Download Page 26

Installing the FWD SCSI Adapter

2–10

7. Verify the operation of the FWD SCSI adapter.

To verify that your system recognizes the FWD SCSI adapter, follow these steps:

a.

Turn on and boot the system, and log in as root or superuser.

b.

In a terminal window, enter the following command:

/etc/ioscan –C scsi 

Enter

 (for HP–UX 9.x)

/usr/sbin/ioscan –C ext_bus 

Enter

 (for HP–UX 10.x)

After a few moments the ioscan utility lists all of the bus interfaces it could find.
The list appears similar to the following:

For HP–UX 9.x:

H/W Path Description Status    

=============================

2.0.1    scsi        ok(0x7071)

2.0.7    scsi        ok(0x707c)

For HP–UX 10.x:

H/W Path  Class          Description

====================================

8/8     ext_bus      GSC add–on Fast/Wide SCSI Interface

8/12/0  ext_bus      Built–in Parallel Interface

8/12/5  ext_bus      Built–in SCSI

If ioscan does not find your FWD SCSI adapter, go to Chapter 3, “Troubleshooting”.

Summary of Contents for Model 744 - VME Workstation

































Reviews:

No comments

Brands by name

Popular brands

Load more brands