manualshive.com logo in svg

HP Model 744 - VME Workstation, Installation And Service Manual

Share
Download
HP Model 744 - VME Workstation Installation And Service Manual Download Page 12

Preparing for the Installation

1–2

Product Description

The followings describes the features, physical and environmental specifications and
parts included with the installation kit.

Features

The HP A4268A FWD SCSI Adapter complies with ANSI X3T9.2 SCSI specifications
and has the following features:

•

NCR 53C720 SCSI I/O processor chip.

•

Differential control and data lines.

•

Internal removable terminators allowing for installation anywhere on the SCSI bus.

•

4 position DIP switch to set SCSI ID for the adapter.

Physical and Environmental Specifications

The HP A4268A FWD SCSI Adapter’s physical and environmental specifications are:

•

Temperature

–

Operating: 0 to 55 degrees C (ramp rate 10 degrees C).

–

Storage: – 40 to 70 degrees C.

•

Humidity:  95% relative humidity at 40 degrees C.

•

Mechanical shock: compliant with IEC 654-3 and IEC-68-2 methods.

•

Mechanical vibration: compliant with IEC 654-3 Class VH3 levels or better.

Summary of Contents for Model 744 - VME Workstation

































Reviews:

No comments

Brands by name

Popular brands

Load more brands