manualshive.com logo in svg

HP Model 744 - VME Workstation, Installation And Service Manual

Share
Download
HP Model 744 - VME Workstation Installation And Service Manual Download Page 15

Preparing for the Installation

1–5

uname  –r  

Enter

A line similar to the following is displayed:

A.09.05

If a number less than 09.05 is displayed it means that you need to update 
your software before installing your HCRX/VME graphics upgrade.

•

For Model 743 and 744 SBCs with HP-RT, the operating system software revision
of the host system must be HP-UX 10.10 or later, and the HP-RT target system must
have at least HP-RT 3.01.  For more information, refer to the HP–RT 3.01 Release
Notes.

Contact your designated service representative for information on receiving an upgrade to
the correct version of the operating system.

3. Record Adapter Information

Record the serial number of the adapter for future reference.  If your adapter needs
service in the future, the serial number will be needed by HP service personnel. This
information is provided on the bar code sticker affixed to the adapter. See the following
example.

401105H009

Summary of Contents for Model 744 - VME Workstation

































Reviews:

No comments

Brands by name

Popular brands

Load more brands