HP Integrity rx2800 - i2 User'S & Service Manual Download Page 90 | Manualshive

Page: 90 / 151

background image

Table 40 Cooling subsystem events that light SID LEDs —

Notes

Source

Cause

Sample IPMI Events

Diagnostic
LEDs

Cleared when fan is
replaced

iLO 3

Fan has either
previously failed or
is degrading

Type 02h, 0Ah:07h:01h
COOLING_UNIT_WARNING

Fans (1-6)

Cleared when fan is
replaced

iLO 3

Fan has failed and
no longer meets
minimum
requirements

Type 02h, 0Ah:07h:02h
COOLING_UNIT_FAILURE

Fans (1-6)

Troubleshooting the I/O

This subsection provides information on troubleshooting issues with the public PCIe slots.

I/O subsystem behaviors

The main role of the I/O subsystem is to transfer blocks of data and instruction words between
physical shared memory and virtual memory (system disks or disk array). The system boot is the
first time blocks of data and instructions are transferred into physical memory from a local disk or
DVD or over the network. This process is referred to as Direct Memory Access (DMA) and is initiated
by I/O devices located in I/O or on Host Bus Adapter (HBA) I/O cards and does not involve any
logical CPUs.

Customer messaging policy

•

Always refer to the SEL for any action from low level I/O subsystem faults as there may not
be any lighted LEDs on the System Insight Display.

•

For configuration style errors, for example, no iLO 3 MP or core I/O HBAs installed or working,
see Supported Configurations subsection for actions.

•

Some diagnostic messages are reported for high level I/O subsystem errors; all fatal I/O
subsystem errors cause global MCAs.

Table 41 I/O subsystem events that light SID LEDs

Notes

Source

Cause

Sample IPMI events

Diagnostic
LEDs

Likely a short on
I/O card or I/O
slot.

BMC

Over-current on PCI slot

Type 02h, 03h:05h:01h

CURRENT_LIMIT_EXCEEDED

I/O Card

A voltage on the
I/O backplane is
out of range
(likely too low)

BMC

Voltage on CRU is
inadequate

Type 02h, 02h:07h:03h

VOLTAGE_DEGRADES_TO_NON_RECOVERABLE

I/O Backplane

A voltage on the
I/O backplane is
out of range
(likely too low)

BMC

Voltage on CRU is
inadequate

Type 02h, 02h:07h:03h

VOLTAGE_DEGRADES_TO_NON_RECOVERABLE

Disk Backplane

90

Troubleshooting

«
...
88
89
90
91
92
...
»

Summary of Contents for Integrity rx2800 - i2
























































































































































Reviews:

No comments

Related manuals for Integrity rx2800 - i2

Brand: Hainbuch Pages: 68

RANGEBOOSTER N 650

Brand: D-Link Pages: 24

Brand: aqprox! Pages: 37

Brand: Sharkoon Pages: 40

Brand: W&T Electronics Pages: 4

Brand: Zonet Pages: 2

Brand: Allen-Bradley Pages: 2

Brand: Emulex Pages: 19

EtherFast 100Mbps Fiber-Optic Adapter SP2515 SERIES

Brand: MicroNet Pages: 10

Brand: MSI Pages: 41

Brand: MSI Pages: 74

Brand: Danfoss Pages: 166

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands